Hope someone can help
- Appo
- Topic Author
- Offline
- New Member
Less
More
- Posts: 6
- Thank you received: 0
2 years 3 months ago #1093
by Appo
Hope someone can help was created by Appo
Try as much as I can, I cannot find the answer, hope someone can help PLEASE.
I have traced an image in editor. how do I then assign it and save it to a key on the live clips. I simply wish to add my logo to the included clips . hope that makes sense ?
hopefully someone can help
Thank you in advance
I have traced an image in editor. how do I then assign it and save it to a key on the live clips. I simply wish to add my logo to the included clips . hope that makes sense ?
hopefully someone can help
Thank you in advance
Please Log in or Create an account to join the conversation.
- admin
- Offline
- Administrator
Less
More
- Posts: 250
- Thank you received: 21
2 years 3 months ago - 2 years 3 months ago #1094
by admin
Replied by admin on topic Hope someone can help
Hi, you simply have to assign the figure to a key.
See here: www.showeditor.com/en/manual/3-first-ste...figures-to-keys.html
Make sure to save the figure first, of course.
The figure must reside in the same folder on the hard drive as the other figures you're using for your live set. So best is to load the live set first before you import the content.
To learn more about how Showeditor works, please also check out this comprehensive video:
See here: www.showeditor.com/en/manual/3-first-ste...figures-to-keys.html
Make sure to save the figure first, of course.
The figure must reside in the same folder on the hard drive as the other figures you're using for your live set. So best is to load the live set first before you import the content.
To learn more about how Showeditor works, please also check out this comprehensive video:
Please Log in or Create an account to join the conversation.
- Appo
- Topic Author
- Offline
- New Member
Less
More
- Posts: 6
- Thank you received: 0
2 years 3 months ago #1096
by Appo
Replied by Appo on topic Hope someone can help
Having real problems, I would like to add my own logo into the included "default live show" I just cannot seem to do it, I have learning difficulties and have read the manual and watched the video time and time again. please if anyone can help ? or even be able to make the file for me I would be most appreciative. Thank you, I hope someone can help.
Please Log in or Create an account to join the conversation.
- admin
- Offline
- Administrator
Less
More
- Posts: 250
- Thank you received: 21
2 years 3 months ago #1097
by admin
Replied by admin on topic Hope someone can help
OK, so steps are:
1. open Live window, hit File -> Load Default Show
2. return back to the main window. you see the table with the figures
3. create new figure and save it to teh SAME folder where the other figures reside (see bottom right part, there is the file structure)
4. right click to the created figure in the figure table and "assign key", then press the key you want to use for it
1. open Live window, hit File -> Load Default Show
2. return back to the main window. you see the table with the figures
3. create new figure and save it to teh SAME folder where the other figures reside (see bottom right part, there is the file structure)
4. right click to the created figure in the figure table and "assign key", then press the key you want to use for it
Please Log in or Create an account to join the conversation.
- Appo
- Topic Author
- Offline
- New Member
Less
More
- Posts: 6
- Thank you received: 0
2 years 3 months ago #1102
by Appo
Replied by Appo on topic Hope someone can help
Thanks for your help so far.
How hard should it be to make this logo ? I just cannot make it, I have tried with the bitmap trace but it looks to make too many points ?
Please is someone able to make the file for me please ? I would be most grateful . Thank you.
Everything else is great with the laser and software, but I only need this logo to go with the included images.
How hard should it be to make this logo ? I just cannot make it, I have tried with the bitmap trace but it looks to make too many points ?
Please is someone able to make the file for me please ? I would be most grateful . Thank you.
Everything else is great with the laser and software, but I only need this logo to go with the included images.
You do not have permissions to access this page.
You do not have permissions to access this page.
Please Log in or Create an account to join the conversation.
- admin
- Offline
- Administrator
Less
More
- Posts: 250
- Thank you received: 21
2 years 3 months ago #1103
by admin
Replied by admin on topic Hope someone can help
Please send your logo file to This email address is being protected from spambots. You need JavaScript enabled to view it. and I'll see what I can do.
But will most probably be tomorrow
But will most probably be tomorrow
Please Log in or Create an account to join the conversation.
- Appo
- Topic Author
- Offline
- New Member
Less
More
- Posts: 6
- Thank you received: 0
2 years 3 months ago #1104
by Appo
Replied by Appo on topic Hope someone can help
Thank you so much . email sent.
Please Log in or Create an account to join the conversation.
- Appo
- Topic Author
- Offline
- New Member
Less
More
- Posts: 6
- Thank you received: 0
2 years 3 months ago #1105
by Appo
Replied by Appo on topic Hope someone can help
Hi, did you get my email please ?
just checking it never hit a spam trap
Thanks in advance
just checking it never hit a spam trap
Thanks in advance
Please Log in or Create an account to join the conversation.
- admin
- Offline
- Administrator
Less
More
- Posts: 250
- Thank you received: 21
2 years 3 months ago #1106
by admin
Replied by admin on topic Hope someone can help
ah, found it, went to spam. will check on it later and sort this for you
The following user(s) said Thank You: Appo
Please Log in or Create an account to join the conversation.
- Appo
- Topic Author
- Offline
- New Member
Less
More
- Posts: 6
- Thank you received: 0
2 years 3 months ago #1107
by Appo
Replied by Appo on topic Hope someone can help
Hi Admin, did you have chance to look at the logo please ?
many thanks
many thanks
Please Log in or Create an account to join the conversation.